美容美發器材TM22突跳式溫控器KSD301溫度控制開關-性少婦JEALOUSVUE片,神馬午夜不卡片メイリン モデルコレクション メ
- 報價
- ￥0.70元每
- 聯系手機
- 15015396189
- 品牌
- 華愷威
- 壽命
- 100000
- 型號
- TM22 KSD301
1.基本信息 Basic Information
1.1執行標準 According to (Standard)
GB/T:《家用和類似用途電自動控制器 第1部分：通用要求》
IEC 730-1:1994 Automatic electrols for household and similaruse. Part 1:General re
GB/T:《家用和類似用途電自動控制器 溫度敏感控制器的特殊要求》
IEC 730-2-9-1992:Automatic electrical controls for householdand similar use Particuar
re for temperature sensing controls
JB/T 3751-1997:《家用和類似用途雙金屬溫度控制器》
JB/T 3751-1997:Bi-meral temperature controls for householdand similar use
1.2構造Structure
1.2.1. 分類 Classification
屬于溫度固定的雙金屬碟片瞬動式溫度控制器。
They are temperature-fixed bi-metal Snap-Action temperaturecontroller
1.2.2.接地方式 Method Of Earth
通過溫控器金屬外蓋與設備接地金屬部件相連。
By means of the metal cup of thermostat connected in theearthing meral part.
1.2.3.外觀及尺寸Appearance
外觀應加工良好，無有損于性能及商品價值的傷、裂、變形、毛刺、污漬等缺陷。
The appearance should be processed well, without any defecteffecting the performance or
value of the merchandise such asstrain,crach,rust,distortion,besmirch,ete.
1.3動作方式Action Forms
■ 室溫下觸點接通（nc），溫度上升觸點斷開，溫度降低觸點恢復接通。
Normal close:Cut out at temperature rise,cut in attemperature decreasing.
□室溫下觸點接通（nc），溫度下降觸點斷開，溫度上升觸點恢復接通。
Normal close:Cut out at temperature decreasing,cut in attemperature rise.
□室溫下觸點斷開（no），溫度上升觸點接通，溫度降低觸點恢復斷開。
Normal open:Cut in at temperature rise,cut out at temperaturedecreasing.
□室溫下觸點斷開（no）, 溫度下降觸點接通，溫度上升觸點恢復斷開。
Normal open:Cut in at temperature decreasing,cut out attemperature rise.
□室溫下觸點接通（nc），溫度上升觸點斷開，溫度降低手動復位接通。
Normal close:Cut out at temperature rise,manual reset attemperature decreasing.
Ⅸ.端子類型Temrinal Type
N:187系列端子（4.8×0.5）187Series
M:187系列端子（4.8×0.8）187Series
R:250系列端子（6.3×0.8）250Series
F:非標端子Not Criterion
Ⅹ.固定形式Holder Type
1:活動固定器Free Holder
2:無固定器 Without the Holder
3:45°固定器45°Holder
4:90°固定器90°Holder
5:180°固定器180°Holder
Ⅺ.絕緣殼體Insul ating Material
D:電木Free Holder
E:陶瓷Without the Holder
P:PPS
2.主要性能Primary Performance
2.1.動作溫度Operating Temperature
2.1.1.溫度特性Characteristic
斷電溫度： 130±5℃
接通溫度： 標準復位
2.1.2. 測試方法Test method
把溫控器夾在測試區內，等待測溫區的溫度平衡后，開始測試。測試爐內以空氣作為加熱
介質，在測溫區放置溫度計或溫度傳感器。在溫度進入動作溫度公差范圍前2K開始，以小于1K/min的溫度變化速率進行加溫或降溫，其間必須進行攪拌，使溫度分布充分均勻；測溫區溫
度分布均勻性在±0.4K以內。
測試裝置可設置通斷顯示裝置。溫控器兩接線端子間電壓大于5V，通過試樣電流大于10mA。
4/
2.2 絕緣電阻 Insulation Resistance
用DC500V絕緣電阻表加額定電壓DC500V測定大于100MΩ。
With a DC500V megger, borne DC 500V,the tested value is over100 MΩ.
2.3 電氣強度Dielectric Strength
帶電金屬部件與非帶金屬部件之間能承受接近正弦波的1500V50Hz交流電壓歷時一分鐘的耐壓試驗，不擊穿，無閃絡。
Parts between elecriferous components and non-electriferousones can bear 1500V 50Hz AC current,
Which is nearly sine wave, for one minute as bearingtest,Resulted no breakdown,no flashover.
2.4.長期工作Zui高環境溫度Max.Ambient temperature
□100℃ □140℃ ■185℃ □205℃ □220℃ □245℃ □280℃ □320℃
3．可靠性測試 Reliability Test
3.1.試驗條件Test Conditions
◆ 環境溫度20±5℃；
◆ 環境相對濕度60%～70%；
◆ 電源應為額定電壓及額定頻率50Hz、60Hz的正弦波電源。
在試驗結果不發生異議的情況下，按下述條件試驗亦可：
◆ 環境溫度5～35℃；
◆ 環境相對濕度45%～85%；
◆ 電源為接近正弦波的交流電；
◆ Ambient temperature: 20℃
◆ Ambient Relative Humidity: 60%～70%；
◆ The power supply should be of sine wave,with rated voltsand rated frequency of50Hz、60Hz;
Without discrepancing the result,test may be implementedaccording to the following conditions;
◆ Ambient temperature varies berween 5～35℃；
◆ Ambient relative humidity varies berween45%～85%；
◆ The power supply should be AC nearly sine wave;
3.2工作壽命Working Life
將溫控器試樣接上額定電壓，Zui大工作電流（偏差±5%），對溫控器給以升、降溫進行觸頭開閉試驗，Zui大頻率6次/min,閉合時間1秒以上。每天閉一次作為一個周期，記錄周期數，不發生因電弧引起的極間短路及對帶電件短路，然后檢查性能。樣品進行周期為10萬次的耐久性試驗后應符合下列性能指標：
◆ 動作溫度對試驗初始值的變化在100℃以下為±5℃，在100℃以上為±5%；
◆ 絕緣電阻100 MΩ以上（用DC500V絕緣電阻表加額定電壓DC500V測定）；
◆ 帶電金屬部件與非帶電金屬部件之間能承受接近正弦波的1500V50Hz交流電壓歷時一分鐘的耐壓試驗，不擊穿，無閃絡；
◆ 機能上無性損傷，手動復位溫控器的復位操作無異常。
5/ Powered the sample thermostats with rated volts andmax.current(windage: 5%),increase and decrease
the temperature to test Opening/Closning of the thermostat’scontacts.The max frequency should be 6
times/min,contact keep closed for one second.Ecery openingand closing is calculated as one circle,make
record of circles.And no short circuit was found.Then checkthe performance.After tested 100,000circles,
the samples accord with the following guideline ofspecifications:
◆Initial value of experiment caused by actiontemperature:
＜ 100℃: ±5℃;≥100℃: ±5%;
◆Insulation resistance over 100MΩmore than (tested by DC500Vmegger,powering with
DC500V);
◆ Parts between electriferous components andnon-electriferous ones can bear 1500V 50Hz
AC current,which is nearly sine wave,for one minute asbearing test.Resulted no breakdown,no flashover;
◆No permanent mechanics’damage.No abnormity od resetoperation for manual reset
Thershover;
3.3 耐低溫、高溫和冷熱沖擊
Resistance of low Temperature & HighTemperature,Cold&heat Strike
將溫控器試樣放置在-20℃的恒溫箱中,在溫度穩定后保持1h,取出放置2h;然后將試樣放置在150℃的恒溫箱中,在溫度穩定后保持1h,取出放置2h;Zui后,將試樣放置在-20±3℃的恒溫箱中
0.5h,取出試樣放置在室溫環境2～3min,再取出在150±3℃的恒溫箱中0.5h,取出放置在室溫環境2～3min作為一個周期,連續進行5個周期。在整個試驗過程中,被測試樣品表面不得出現疑露或水滴。完成后,樣品應符合下列性能指標:
◆ 動作溫度對試驗初始值的變化在100℃以下為±3℃,在100℃以上為±3%;
◆ 絕緣電阻100MΩ以上(用DC500V絕緣電阻表加額定電壓DC500V測定);
◆ 帶電金屬部件與非帶電金屬部件之間能承受接近正弦波的1500V 50Hz交流電壓歷時一分鐘的耐壓試驗，不擊穿，無閃絡；
Sample thermostats are placed in the constant-temperature boxwith the temperature of -20℃.When
temperature inside levels off, keep it for 1h.Than take thesamples out and place for 2h,And ten place
Them in the constant-temperature box with the temperatuer of150℃,keep for 1h after temperature,
lecels off, and take out and place for 2h.Finally,keep thesamples in the constant-temperature box of -20
±3℃ for 0.5h,then take out and place then in roomtemperature.(2～3min as oen circle,and for 5 circles
In a row.)During the experiment,no coagulation or drips isever found on the surface of the asmples. When experimentfinished,samples should accod with the following guideline ofspecifications:
◆Initial value of experiment caused by actiontemperature:
＜ 100℃: ±3℃;≥100℃: ±3%;
◆Insulation resistance over 100MΩmore than (tested by DC500Vmegger,powering with
DC500V);
◆ Parts between electriferous components andnon-electriferous ones can bear 1500V 50Hz
AC current,which is nearly sine wave,for one minute asbearing test.Resulted no breakdown,no flashover;
6/
3.4. 耐潮濕 Dampness Resistance
將溫控器試樣按GB2423.3規定放入溫度40±2℃、相對濕度的恒溫箱內48h后,
樣品應符合下列性能指標:
◆ 動作溫度對試驗初始值的變化在100℃以下為±3℃,在100℃以上為±3%;
◆ 絕緣電阻100MΩ以上(用DC500V絕緣電阻表加額定電壓DC500V測定);
◆ 帶電金屬部件與非帶電金屬部件之間能承受接近正弦波的1500V 50Hz交流電壓歷時一分鐘的耐壓試驗，不擊穿，無閃絡；
Samples thermostat are sealed in the instrument(constanttemperature&constant humidity),detailed
as temperature of 40±2℃ relative humidity of 90%～95%,as perregulations ofGB2423.3.A fter placed
for 48h,the samples should accord with the followingguideline of specifications:
◆ Initial value of experiment caused by actiontemperature:
＜ 100℃: ±3℃;≥100℃: ±3%;
◆ Insulation resistance over 100MΩmore than (tested by DC500Vmegger,powering with
DC500V);
◆ Parts between electriferous components andnon-electriferous ones can bear 1500V
50HzAC current,which is nearly sine wave,for one minute asbearing test.Resulted no breakdown,no flashover;
3.5. 耐振動 Vibration Resistance
把溫控器試樣固定在有充分強度的板上,對上下、前后、左右各方向,以頻率20～25Hz振幅3
mm來回時間5min,歷時各1h。完成后,樣品應符合下列性能指標:
◆ 動作溫度對試驗初始值的變化在100℃以下為±3℃,在100℃以上為±3%;
◆ 絕緣電阻100MΩ以上(用DC500V絕緣電阻表加額定電壓DC500V測定);
◆ 帶電金屬部件與非帶電金屬部件之間能承受接近正弦波的1500V 50Hz交流電壓歷時一分鐘的耐壓試驗，不擊穿，無閃絡；
Sample thermostats are fixed on the surface of board withfull intension,Then vibrate the samples with fre～25Hz,swing3mm,come-and-go time 5mm,in dierctions offluctuation,front-back,
left-tight,for 1h,After tested,the samples should accord withthe following guideline of specifications:
◆ Initial value of experiment caused by actiontemperature:
＜ 100℃: ±3℃;≥100℃: ±3%;
◆ Insulation resistance over 100MΩmore than (tested by DC500Vmegger,powering with
DC500V);
◆ Parts between electriferous components andnon-electriferous ones can bear 1500V
50HzAC current,which is nearly sine wave,for one minute asbearing test.Resulted no breakdown,no flashover;
3.6. 耐跌落 Falling Resistance
溫控器試樣從200mm高自由跌落在水泥地、石板或鋼板等堅固的水平面上,分別作上、下、左、右、前、后各落下一次。完成后,樣品應符合下列性能指標: 7/
◆ 動作溫度對試驗初始值的變化在100℃以下為±3℃,在100℃以上為±3%;
◆ 絕緣電阻100MΩ以上(用DC500V絕緣電阻表加額定電壓DC500V測定);
◆ 帶電金屬部件與非帶電金屬部件之間能承受接近正弦波的1500V 50Hz交流電壓歷時一分鐘的耐壓試驗，不擊穿，無閃絡；
溫控開關，熱保護器，限溫器，恒溫開關，溫控器，溫度保險絲
電子商務、技術研發與咨詢。(依法須經批準的項目，經相關部門批準后方可開展經營活動)〓
惠州市華愷威電子科技有限公司是一家經國家工商局批準的一般納稅人企業。專業研發﹑生產與銷售各類溫控器、溫控開關、溫度開關、熱保護器、溫度保險絲等電子元器件。公司擁有自主研發溫度控制器的團隊和自主研發全自動化生產設備的團隊，同時擁有一批技術熟練的技師和操作人員。公司產品的主要研發人員均是國內熱保護器行業的資深工程師，受過國外溫度保護器權威廠家的深造培訓，產品質量和技術水平在同行業中處于領先地位。公司采用歐美管理模式，聘請外企管理人員并出國深...