印花彩板是指通過轉印或覆膜技術等手段將各類花紋印刷在鍍鋅板、鍍鋁鋅等基板上的一種彩涂板。應用較廣的主要有大理石紋、迷彩、木紋等印花彩板，其色彩鮮亮、花色繁多。廣泛應用于家電、家具、門窗、室內外裝飾等領域。

由于鋼鐵行情變動較快，請以當日電詢價格為準。謝謝

用細度來判定彩涂板涂料性能指標

細度是測定彩涂板涂料內顏料、體質顏料等顆粒的大小和分散的均勻程度，單位以微米勻，對外觀和裝飾性能均起到美化作用，且有良好的力學性能等。(pm)表示。彩涂板卷材涂料的背面漆和面漆對細度的要求均很高，一般控制在15~25pm，而底漆的細度則可以粗一些，一般控制在20-40pm。通常來說，細度小，能使涂層平整均細度的測定主要采用量程為50um 的刮板細度計(見圖 4-2)，檢驗方法及標準等效采用幾種規格。另配有一把刮刀。雙刃均磨光。用國標GB1724-89(79)彩涂板涂料細度測定法。刮板細度計的構造為一磨光的平板，由工具合金鋼制成。板上有一溝槽，在槽邊有刻度線，分為0-50pm、0-100pm、0-150m等

測量時需要注意以下幾點:
(1)根據不同涂料類型選用不同量程范圍的細度計，可先用范圍大的細度計粗測。(2)在測板上端滴人涂料樣品1~2g左右，不要過多或過少。
(3雙手握住刮刀，使刮刀與磨光平板表面垂直接觸，以適宜的度由溝槽的深部向淺部拉過(一般用 3s時間)，使試樣充滿溝槽而平板上不留余料。

(4)在陽光下迅速讀數(不應超過 5)，使視線與溝槽表面成 15*-30°角，以出現三個以上顆粒均勻顯露處讀數為準。

Fineness is to measure the size and dispersion uniformity ofpigment and physical pigment particles in coatings. The unit ismicron, which beautifies the appearance and decoration performance,and has good mechanical properties. (PM) denotes. The fineness ofthe back and top coats of coil coatings is very high, generallycontrolled at 15 ~ 25pm, while the fineness of the primer can becoarser, generally controlled at 20-40pm. Generally speaking, smallfineness can make the coating smooth and uniform
The measurement of fineness mainly adopts the scraper finenessmeter with a measuring range of 50um (see Fig. 4-2), and theinspection method and standard are adopted
Several specifications. The other is e with a scraper. Bothblades are polished. The national standard GB 1724-89 (79) was usedto determine the fineness of coatings. The structure of the scraperfineness meter is a polished flat plate made of tool alloy steel.There is a groove on the plate and a scale mark on the edge of thegroove, which is divided into 0-50pm, 0-100pm, 0-150m, etc
The following points should be noted during measurement:
(1) The fineness meter with different measuring range can beselected according to different coating types, and the finenessmeter with large measuring range can be used for rough measurementfirst. (2) Drop about 1 ~ 2G coating sample on the upper end of thetest plate, not too much or too little.
(3) hold the scraper with both hands, make the scraper contact withthe surface of the polished plate vertically, and pull it from thedeep part of the groove to the shallow part at an appropriatedegree (generally takes 3S), so that the sample is filled with thegroove and no residual material is left on the plate.
(4) Read in the sunlight (no more than 5), so that the lineof sight is at an angle of 15 * - 30 ° with the groove surface, andthe reading at the place where more than three particles are evenlyexposed shall prevail