zoriver陶瓷電容壓力變送器ys1液體,

氣體,蒸汽壓力,液位

ys1 陶瓷電容壓力變送器ys1（ys-1）
ys1 ceramic capacitance pressure transmitter

    概述generalremark
   ys1(ys-1)型陶瓷電容壓力變送器采用具有國際先進水平的陶瓷電容壓力傳感器，配合高精度電子元件，經嚴格的工藝過程裝配而成。它采用無中介液的壓力測量技術，充分發揮了傳感器的技術優勢，使變送器具有優異的性能，同時抗過載和抗沖擊能力強、溫度漂移小、穩定性高、具有很高的測量精度。
    ys1(ys-1) ceramic capacitance pressuretransmitter adopts internationally advanced ceramic capacitancepressure sensor, fitted with high accuracy electronic elements,through strict process assembly. it adopts no medium li technology, fully perform transmitter s technicaladvantage, make transmitter s more excellent function, meanwhilestronger anti overload and anti impact ability, small thermo drift,high stability, high measuring accuracy.

   ys1(ys-1)型陶瓷電容壓力變送器具有多種量程、多種連接形式及多種接液材質?？蓮V泛用于石油、化工、電力、冶金、制藥、食品等許多工業領域，可適應各種工業場合及介質，是傳統壓力表及傳統壓力變送器的理想升級換代產品，是工業自動化領域理想的壓力測量儀表。陶瓷電容壓力變送器廣泛應用于液體、氣體、蒸汽壓力測量，液體液位測量。

    ys1(ys-1) ceramiccapacitance pressure transmitter has many range, connection typesand wetted materials. widely used in petroleum, chemical, power,metallurgy, pharmaceutical, food industries etc, suitable forvarious industrial environments, is ideal upgrade replacement oftraditional pressure gauge and traditional pressure transmitter, isideal pressure measuring instrument in industrial automatization.ceramic capacitance pressure transmitter is broadly used in liquid,gas, steam pressure measurement, liquid levelmeasurement.

 

   特點characteristic
    ● 精度高，穩定性好。
       high accuracy, goodstability

    ● 二線制工作方式，4～20ma信號輸出。
       2 line working type, 4~20masignal output

    ●敏感部件及線路板采用全固體結構，堅固抗振。
       sensitive component andcircuit board are in solid construction, rigidvibration-proof
    ● 抗干擾能力強，溫度穩定性好，防爆殼體結構，可全天候使用。
       excellent interference-proof,good thermal drift, explosion-proof enclosure structure,weather-proof
   ● 具有Zui優良的防腐性能，保證的使用可靠性。
       most outstandingcorrosion-proof, ensure best utilityreliability
    ●結構輕巧，簡單合理，無須支架，無須水平安裝，可直接任意位置安裝。

      light construction, simple reasonable, no bracket required, nohorizontal mounting required, available mounting at anyposition.

   工作原理workingprinciple

   變送器由傳感器與電子元件線路組成，被測介質的壓力直接作用于傳感器的陶瓷膜片上，使膜片產生與介質壓力成正比的微小位移，正常工作狀態下，膜片Zui大位移不大于0.025mm，電子線路檢測這一位移量后，即把這一位移量轉換成對應這一壓力的標準工業測量信號即（4～20ma）。
    transmitter is composed of sensor and electronicelement circuit, pressure of measured medium directly applies onsensor s ceramic diaphragm, force diaphragm to displace tinily inproportion to pressure of medium, under normal working condition,diaphragm displace no more than 0.025mm, electronic circuit detectsthis displacement, and convert it into standard industrialmeasuring signal i.e. (4~20ma) corresponding to thispressure.

   超壓時膜片直接貼到堅固的陶瓷基體上，由于膜片與基體的間隙只有0.1mm，過載時膜片的Zui大位移只能是0.1mm，(此時測量膜片貼到陶瓷支架上，避免損壞)所以從結構上保證了膜片不會產生過大變形。由于膜片采用高性能的工業陶瓷，因而使傳感器具有很強的抗沖擊及抗過載能力。從襯底電極①和膜片電極②之間可以檢測到與壓力成比例的電容變化量，電容的變化值經激光微調電路放大輸出高達0.5-4.5v的直流電壓，計算機可直接采樣。

    when overpressure,diaphragm directly stick to solid ceramic base body, as there isonly 0.1mm gap between diaphragm and base body, when overpressure,the maximum diaphragm displacement could be no more than 0.1mm, (atthat time, measuring diaphragm sticks to ceramic bracket, avoiddamage) so structurally prevent diaphragm from excessivedeformation. because diaphragm adopts high functional industrialceramic, sensor is significantly shock-proof and overload-proof.from between lining electrode① and diaphragm electrode②capacitancevariant in proportion to pressure can be detected, capacitancevariant value is amplified by laser micro adjustment circuit tooutput direct voltage as high as 0.5-4.5v, computer can sample itdirectly.

 

    圖-1 ys-1型陶瓷電容壓力變送器原理圖
    figure - 1 ys1 type ceramic capacitance pressuretransmitter principle scheme

       主要技術指標 main technicallndex
    技術指標technical index
    使用對象液體、氣體或蒸汽等
     utility object: liquid, gas or steametc
    測量范圍表壓：0～1kpa～7mpa; 負壓：-100kpa～7mpa
    measuring range: gauge pressure:0~1kpa~7mpa;minus pressure; -100kpa; 7mpa
    輸出4～20ma.dc
    output: 4~20ma.dc

    電源13～30v.dc
    power supply: 13~30v.dc
    負載特性4～20 ma.dc 二線制負載r ≤ 50(v-13)（見圖-2）
    load characteristic: 4~20 ma.dc 2 line load ≤50(v-13)(see figure-2)
    溫度范圍環境溫度：-20～+70℃ ;存儲溫度：-40～+85℃
    temperature limit: ambient temperature：-20～+70℃; storage temperature：-20～+80℃

   標準介質溫度：-30～+85℃（短時可達130℃）
    standard medium temperature: -30~+85℃short timeup to 130℃
    外殼防護ip65
    enclosure protection: ip65
    防爆標志本安型exia ⅱ ct5 ; 防爆合格證編號：ce042114
    explosion-proof mark: intrinsically safety typeexiaiict5 ;
        explosion-proofcertificate of conformity no.: ce042114

     

 

 

             負載特性（圖-2）load characteristic（figure-2）

 

        (transmitter s loadcharacteristic diagram)
        負載電阻: loadresistance
        電源電壓：power supplyvoltage
        工作區: workingarea

 

   性能指標functional index
    綜合精度提供標準±0.25%bfsl/年，Zui高精度± 0.1% bfsl/ 年
    general accuracy: supply standard ±0.25%bfsl/year，

        maximum accuracy ±0.1% bfsl/year

    穩 定 性優于± 0.1% bfsl/年
    stability: better than ± 0.1%bfsl/year

   溫度影響在-20～+70℃范圍內，變化量小于± 0.18%/10℃
    thermal effect: within-20～+70℃，variation below ±0.18%/10℃
    振動影響在任何方向上振動頻率為20-200hz時，變化量小于± 0.02% bfsl/年
    vibration effect: in any direction,uency 20-200hz，

        variation below ±0.02% bfsl/year
    沖擊影響任何方向100g 沖擊11ms 后，變化量小于± 0.02% bfsl
    impact effect: in any direction 100g impactafter 11ms,

        variation below ±0.02% bfsl
    負載影響只要輸入變送器的端子電壓高于13v，就無負載影響。
    load effect: no load effect as long as voltageinput to transmitter s terminal greater than 13v.
    位置影響無
    position effect: none

 

   結構指標constructional index
   結構材料constructionalmaterial:

      膜片材質：氧化鋁陶瓷
      diaphragm material：aluminiumoxide ceramic
      外殼材質：鋁合金石鑄
      enclosure material：aluminium alloystone cast
      接觸介質材質：sus304
      wetted material：sus304
     “ o”型圈氟橡膠 （或聚四氟乙烯）
     “ o”type ring fluoroelastomer （orptfe）
    過程連接標準提供m20 × 1.5 陽螺紋
    process connection: supply standard m20×1.5 malethread

   電氣連接可根據需要從任何一個出口引出，建議使用φ 10工業電纜作為引線，以便密封。引出接頭可選用通用電纜接頭pg16或m20×1.5，不引線一端用端蓋封住。
    electric connection:on request lead from anyexit, suggest φ10 industrial cable as lead, so that it is sealed.leadout socketcould be generalcable socket pg16 or m20×1.5，use end cap to seal no leadend.

 

   結構及安裝方式construction and mountingoptions

   

    圖-3 ys1壓力變送器外型尺寸圖

    figure-3 ys1pressure transmitter external dimension drawing

    1.直接安裝在測量點上（任意角度）。
       directly mount on measuringpoint（any angle）
    2. 盡量安裝在溫度梯度與溫度波動小的測壓點上，同時避免強振動和沖擊。
       suggest mount on measuringpoint with lower temperature gradient and temperature fluctuation,meanwhile avoid vibration and impact.
    3.室外安裝時，盡可能放置于保護盒內，避免陽光直射和雨淋，以保持變送器性能穩定和延長使用壽命。
       in case of outdoor mounting,preferred mounting in protection case, avoid direct exposure tosunlight and rainfall, to maintain transmitter s functionalstability and longer service life.
    4.測量蒸汽或其它高溫介質時，注意不要使變送器的工作溫度超限。必要時請安裝散熱器或其它冷卻裝置連接。
       when measuring steam or otherhigh temperature media, make sure transmitter s working temperaturelimit is observed. fit cooler or other cooling device ifnecessary.
    5.安裝時應在變送器和介質之間加裝壓力截止閥，以便檢修和防止取壓口堵塞而影響測量精度。在壓力波動范圍大的場合還應加裝阻尼器或壓力緩沖裝置。
       when mounting, shut valveshould be used between transmitter and medium, for easy maintenanceand to prevent pressure taking port from blocking that influencesmeasuring accuracy. damper or pressure buffer should be used wherebig pressure fluctuation exists.

   注：不得隨意更換或改動可能影響防爆性能的元器件或結構。
    note：random replacing or altering elements orconstruction that may impair explosion-proof function isprohibited.

    系統連接及調試s y s t e m connection andadjustment

   變送器在測量系統中的連接見圖4。建議電源電壓vs 選用24v.dc。
    connection of pressure transmitter in measuringsystem refers to figure 4. suggest power supply vs uses 24v.dc。
    二次儀表中采樣電阻（負載電阻）rl 的阻值選用250 ω。如果us 和rl選用別的數值，
那么rl = 值不能超過由公式計算得到的數值。電源通過信號線接到變送器，變送器頂部兩側面的連接孔用電纜密封或信號線裝配，信號電纜通過緊固螺母鎖緊，不使用的連接口必須密封。
    sampling resistance in secondary instrument（loadresistance）rl uses 250 ω。if
resistance deviates for us and rl, rl value shall not exceed thevalue from formula
rl= power supply is connected to transmitter via signal cable,connections holes at both sides of top of transmitter is sealedwith cable or assembled with signal cable, signal cable is fastenedby lock nuts, idle connection hole must be sealed.
    a：測量系統接線圖measuring system wiring scheme
    在系統回路中必須采用屏蔽信號電纜，并可靠接地。

    shielded signalcable must be used in system loop, and must be groundedfirmly.

 

                                  圖-4 測量系統示意圖（4～20ma）
                            figure-4 measuring system scheme（4～20ma）

 

   b：本安型壓力變送器intrinsicallysafety type pressure transmitter
    ys1本安型壓力變送器采用本質安全電路，適用于爆炸危險區域，防爆等級exiaiict5(防爆合格證編號：ce042114)，技術性能指標與普通型壓力變送器相同。在系統回路中必須采用屏蔽信號電纜，并可靠接地。

    ys1 intrinsicallysafety type pressure transmitter adopts intrinsically safetycircuit, suitable for explosive hazardous zone, explosion-proofclass exiaiict5(explosion-proof certificate no.：ce042114)，technicalfunction index is same as standard pressure transmitter. shieldedsignal cable must be used in system loop, and must be groundedfirmly.

                                圖-5 本安型測量系統示意圖（4～20ma）
                   figure-5intrinsically safety measuring system scheme（4～20ma）

   變送器出廠前已根據用戶需求，量程、精度均已調到精度范圍以內，一般不需校驗。但以下情況需重新校驗：
    before delivery transmitter has been set range,accuracy within accuracy range as per customer s request, normallydoesn t need calibration but as a exception if following situationsoccur：

    a.運輸途中出現跌落、強烈震顛和碰撞；
       falling down, strongshock and vibration in transit；
    b. 存放期超過一年；
       over 1 year storage

    c.長時間運行后，出現大于精度范圍內的誤差；
       long time operation, erroroccurs greater than accuracy range;
    d. 使用單位的例行檢驗；
       user s routineinspection；

 

   如何選擇壓力變送器（具體訂貨時參考）
   how tochoose pressure transmitter（refer to when ordering）
    (1) 確定測量介質decide measuring medium
       根據腐蝕程度的大小選擇相應的變送器，一般來說非強酸、強堿均可使用以不銹鋼為隔離單元的變送器，否則只能選擇專為防腐蝕設計的鈦合金等特制變送器。其次還需看測量介質是否粘稠度，干凈程度，如果粘稠介質就需要選擇硬性隔離單元的變送器。
    choose corresponding transmitter accordingto corrosivity, normally transmitter with stainless steel isolationcell is enough for non strong acid strong alkali, otherwise specialchemical seal product made in titanium alloy specially designed forcorrosion-proof must be used. secondly, need to know viscosity ofmeasuring medium, cleanliness, in case of very viscous transmitterof rigid isolation cell needs to be used.
    (2) 確定測量范圍和測量方式

        decide measuringrange and method
    一般選擇測量范圍時要考慮實際測量范圍，過壓測量范圍，選擇量程以Zui大測量范圍為準，同時考慮過壓測量范圍的大小。另外需要選擇正確的測量方式，如果測量差壓必須選擇差壓變送器。
    normally when choosing measuring range, need toconsider actual measuring range, overpressure measuring range,choosing range should refer to the biggest measuring range,meanwhile consider volume of overpressure range. in addition, needto choose correct measuring method, if measuring pressuredifference, need to use differential pressure transmitter
    (3) 確定精度范圍，補償溫度范圍，使用溫度范圍

     decideaccuracy range, compensation temperature range, using temperaturerange.
    根據需要測量的Zui低精度，一般選擇略高于所要求Zui低精度的產品。 選擇時還需考慮長期穩定性指標。所謂補償溫度范圍即正常工作時測量介質的溫度范圍，使用溫度范圍即使用過程中可能出現的Zui大溫度范圍，一般選擇時略大于測量介質的溫度范圍。
    according to minimum accuracy, normally choose abit higher accuracy meanwhile when choosing, need to consider longterm stability compensation temperature range is that measuringmedium s temperature range when working normally, using temperaturerange is the biggest temperature range when using, normally choosea little bigger temperature range than re
    (4) 確定供電電源、輸出信號、壓力螺紋接口、電氣接口、機械尺寸等
        decide pressureconnection, electric connection, mechanical dimensions etc
    (5) 確定是否需要防爆，需要防電磁干擾，以及外殼防水的環境指標

       decide if need explosion-proof, electro magneticinterference-proof, and ambient factor of water-proof ofenclosureys1

    選型表 how toorder ysz
    型號代碼特性說明codeintroduction
    基本型號basic type
        ys1 = 陶瓷電容壓力變送器
        ceramic capacitancepressure transmitter
    輸出signal output
        420  =24v,4-20ma
        015  =24v, 1-5v
    精 度accuracy

        010 =0.1級±0.1％
        025 =0.25級±0.25％
        050 =0.5級±0.5％
    測量 范 圍ranges
       在0-7mpa之間選項具體代碼請參看量程對照表see range table

    儀表連接connection
        m20 =m20 x1.5或其它連接標準other connections

 

歡迎來電咨詢訂購zoriver陶瓷電容壓力變送器ys1液體,氣體,蒸汽壓力,液位

電話:010-51930

傳真：010-51669912

115 2636968574

郵箱：[email protected]

公司官網：https://www.zoriver.cn   https://www.zoriver.com.cn

本產品的加工定制是是，品牌是Zoriver/卓爾瑞華，型號是YS1，類型是陶瓷型壓力變送器，測量介質是液體、氣體或蒸汽等，測量范圍是表壓：0～1KPa～7MPa（kPa），精度等級是±0.25%BFSL/年，輸出信號是4～20mA.DC（mA），防爆等級是本安型ExiaⅡCT5，防護等級是IP65，電源電壓是13～30V.DC（V），接口尺寸是標準提供M20×1.5陽螺紋（mm）