三螺桿泵  3GR85×2W21 燃油輸出 低噪音無脈動 泊頭廠家生產

4、螺旋角：5、結構特性與軸封：

符號

結構說明

適用范圍

U

內置滾動軸承

-

介質潤滑性良好，溫度小于80℃

1.0

骨架油封

介質潤滑性良好，立式安裝

2.0

2機械密封材料組合為硬對石墨

0表示密封的結構型式（不同型式機封按順序號依次排列，如2.1，2.2）

6、材料組合：

材料組合代碼

泵體

襯套

材料組合代碼

泵體

襯套

W11

HT200

HT200

W14

HT200

ZL109

W12

ZCuSn5Pb5Zn5

W22

焊接Q235

ZCuSn5Pb5Zn5

7、特殊要求：S表示用戶特殊要求，據不同要求分別以S1～S10區分表示，具體序號由工廠提供。

●3三螺桿泵工作原理:

　　3G型三螺桿泵是轉子型容積泵，適于輸送各種不含固體顆粒，無腐蝕性油類及類似油的潤滑性液體、輸送液體粘度2~760mm2/s，溫度不超過80℃,超過80℃可用高溫泵3GW型。3g type is three screw pump rotor type positive displacement pump,is suitable for conveying various not containing solid particles,non-corrosive oil lubricity and similar oil liquid,uid viscosity was 2 to 760 / s, temperature not over 80℃, morethan 80℃high temperature pump available 3 gw type.

   3G型三螺桿具有多種結構，一般小流量泵襯套和泵體合為一個，可以臥式和立式安裝。進油口方向可相隔90°任意安裝，軸封多數為機構密封。中等流量以上泵，襯套為一個單獨的零件固定于泵體內，螺桿軸端裝有平衡環以液力平衡其軸向力。一般結構為臥式。進油口方向亦可以相隔90°任意安裝。改變泵體后可制成立式。軸封根據情況有機械密封和軟填料密封兩種結構。Threescrew with multiple structure of 3 g, general small flow pumpbushings and pump body into one, can be installed in a horizontaland vertical.Oil inlet direction can be 90°apart any installation,most of the shaft sealing seal for your organization.The mediumflow in pump, bushing as a separate component fixed in the pumpbody, screw shaft end is e with the gimbal ring to hydraulicbalance the axial force.The general structure is horizontal.Inletdirection also can be 90°apart any installation.After the change ofpump body can be made into vertical.Depending on the situation ofthe shaft sealing with mechanical seal and soft packing seal twostructures.

   3G型三螺桿泵軸伸支承較小，應由原動機經彈性聯軸器直接驅動，不得用皮帶輪等會產生額外徑向力較大的傳動方式傳動。3g type three-screw pump shaft and bearing is small, should bedriven by a prime mover directly by the elastic coupling, shall notbe used pulley will produce additional radial force largetransmission way.

●3G三螺桿泵輸送各種油類時應注意事項：When conveying various oil mattersshould be paid attention to:

   1、輸送40~150mm2/s的油類Zui合適，允許按泵的Zui高工作壓力使用。2、輸送40mm2/s以下的油類，為保證泵的流量及壽命應降壓使用。3、輸送150mm2/s以上的油類，且進油管道過長，彎頭過多，泵工作時如產生噪音或振動現象，則應考慮更換低一級轉速的電機運轉或縮短吸入管道，減少彎頭。1,delivery was 40 ~ 150 / s best oils, permitted to use according tothe maximum working pressure of pump.2, transmission oil, under 40was/s in order to ensure the pump flow and life should be usedantihypertensive.3, transmission of more than 150 was/s oils, andthe oil inlet pipe is too long, too much bend, such as noise orvibration phenomenon when the pump work, should consider to replacethe low level of rotational speed of motor operation or shorten thesuction pipe, reducing elbow.

 ●3G型三螺桿泵安裝要求:3 g type three-screw pump installationre:

   1、安裝前應檢查泵的油封是否良好，并檢查泵在運輸中是否損壞，可用手轉動聯軸器是否有卡勁現象，如有則應拆泵進行清洗，修理和校正。1,before installation should check whether the oil seal of the pumpis good, and check the pump is damaged in transportation, turn thecoupling usable hand card trouble phenomenon, if there is anyshould tear open pump for cleaning, repair andcalibration.2、安裝泵的進油和排油管道時，其管徑不得小于泵的進油和出油口口徑，進油管道不得過長，彎頭不得過多，否則將影響泵的工作狀態。2,installation of pump suction and discharge of oil pipe, the pipediameter shall not be less than the oil inlet of the pump and theoil outlet diameter, inlet pipe shall not be too long, elbow shallnot too much, otherwise will affect the pump workingcondition.3、當有兩臺以上的泵安裝在同一條主管線上，為便于泵的啟動，在近泵的排油管上必須安裝逆止閥。3, when morethan two head of pump installed in the e line, to facilitate pumpstart-up, in close to the oil drain pump must be installed on anon-returnvalve.4、對于在較高溫度（指60℃以上）下輸送粘度大的油類（如：重油）的備用泵，必須是熱備用泵，否則泵在低溫下啟動會造成電機過載或泵損壞。（建議在靠近泵的排油管上的逆止閥旁，并聯安裝一個小回流閥，對備用泵可微啟回流閥，使泵緩慢逆轉，其逆轉速≤100轉/分，使部分熱油經常流過泵內，達到泵熱備用目的）。4,for under high temperature (above 60℃) conveying the viscosity ofoil (such as: heavy oil) of the standby pump, it must be hotstandby pump, otherwise the pump at low temperature can cause thedamage of motor overload or pump.(suggest near the exhaustnon-return valve on the tubing pump, a small return valve installedin parallel, differentiable and the backflow preventer to standbypump, the pump slow reversal, the reverse speed 100 r/min or less,often make some hot oil flows through the pump, to pump hot standbypurposes).5、輸送介質內含有機械雜質。將嚴重影響泵的運轉和降低使用壽命，因此在泵安裝前，必須仔細清除進油管內的焊渣，沙粒等雜質，并應在進油管道靠近泵處安裝濾器，濾器網孔大小，可根據工作情況及介質粘度確定。（一般可用40~80目網），過濾面積一般不得小于進油管橫截面積的20倍。5,mechanical impurity is contained within the transmissionmedium.Will seriously affect the operation and reduce the servicelife of pump, so before the pump installation, must be carefullyclean up the feed tube welding slag, impurities such as grains ofsand, and shall be installed in the inlet pipe near the pumpfilter, filter mesh size, is decided according to the workingcondition and medium viscosity.Available (40 ~ 80 mesh net), filterarea generally shall not be less than 20 times into thecross-sectional area of the tubing6、盡量在泵進油和排油口處的螺紋孔上連接壓力表和真空表，以便于觀察泵的運轉狀態。6, as far as possible inthe pump suction and discharge of oil on the threaded hole mouthconnect pressure gauge and vacuum gauge, in order to observe thepump runningstate.7、原動機與泵的轉軸必須在同一中心線上，可用直尺測隙規在聯軸器圓周上間隔90°處檢查。8、原動機與泵的轉向必須一致，嚴格禁止原動機驅動泵逆轉。電機接線時，應先脫開電機與泵的聯軸器，對電機作試運轉。使其轉向與泵的轉向標志一致。7,prime mover and the pump shaft must be in the e center line,available ruler feeler gauge in the coupling of the circumferenceof a circle by 90°in check.8, steering engine and pump must beconsistent, strictly prohibited prime motor driven pumpreversal.Electrical wiring, should first release coupling of motorand pump, a test run on the motor.The steering pump and steeringsign agreement

●水電行業業績:

1.安徽省淮北發電廠

泵型號:3G60*4C壓力4.0Mpa,流量13.2m3/h,配用電機22kw-4

      3G100*4C壓力4.0Mpa,流量48.42m3/h,配用電機90kw-4

2.湘潭發電有限責任公司

泵型號:3G85*4C壓力4.0Mpa,流量43.2m3/h,配用電機75kw-4

      3G85*42壓力4.0Mpa,流量43.2m3/h,配用電機75kw-4

3.陜西渭河發電廠

泵型號:3G45*3C2壓力1.0Mpa,流量6.72m3/h,配用電機4kw-4

      3G70*3C壓力1.0Mpa,流量16.02m3/h,配用電機7.5kw-4

4.廣西巖灘水電廠

泵型號:3G90*3C2壓力1.0Mpa,流量54.72m3/h,配用電機30kw-4

      3G80*3C壓力1.0Mpa,流量35.04m3/h,配用電機15kw-4

5.陳村水力發電廠

泵型號:3G45*4G壓力4.0Mpa,流量11.1m3/h,配用電機18.5kw-4

       3G90*4GR46U1.0W11壓力:4.0Mpa,流量51.48m3/h,配用電機90kw-4

6.王快水電廠

泵型號:3G55*4G40U1.0W11壓力1.0Mpa,流量9.72m3/h,配用電機5.5kw-4

       3G60*4GR46U1.0W11壓力1.0Mpa,流量16.26m3/h,配用電機7.5kw-4

7.張家界水電開發公司

泵型號:3G85*4G46U1.0W11壓力1.0Mpa,流量48m3/h,配用電機22kw-4

       3G100*4GR54U1.0W11壓力1.0Mpa,流量100.5m3/h,配用電機45kw-4

8賀龍水電廠

泵型號:3G80*4G44U1.0W11壓力1.0Mpa,流量35.58m3/h,配用電機15kw-4

       3G70*4GR54U1.0W11壓力1.0Mpa,流量33.66m3/h,配用電機15kw-4

9.魚潭水電廠

10.陜西石泉水力發電廠

泵型號:3G55*4G46U1.0W11壓力1.0Mpa,流量12.18m3/h,配用電機5.5kw-4

   1、安裝前應檢查泵的油封是否良好，并檢查泵在運輸中是否損壞，可用手轉動聯軸器是否有卡勁現象，如有則應拆泵進行清洗，修理和校正。1,before installation should check whether the oil seal of the pumpis good, and check the pump is damaged in transportation, turn thecoupling usable hand card trouble phenomenon, if there is anyshould tear open pump for cleaning, repair andcalibration.2、安裝泵的進油和排油管道時，其管徑不得小于泵的進油和出油口口徑，進油管道不得過長，彎頭不得過多，否則將影響泵的工作狀態。2,installation of pump suction and discharge of oil pipe, the pipediameter shall not be less than the oil inlet of the pump and theoil outlet diameter, inlet pipe shall not be too long, elbow shallnot too much, otherwise will affect the pump workingcondition.3、當有兩臺以上的泵安裝在同一條主管線上，為便于泵的啟動，在近泵的排油管上必須安裝逆止閥。3, when morethan two head of pump installed in the e line, to facilitate pumpstart-up, in close to the oil drain pump must be installed on anon-returnvalve.4、對于在較高溫度（指60℃以上）下輸送粘度大的油類（如：重油）的備用泵，必須是熱備用泵，否則泵在低溫下啟動會造成電機過載或泵損壞。（建議在靠近泵的排油管上的逆止閥旁，并聯安裝一個小回流閥，對備用泵可微啟回流閥，使泵緩慢逆轉，其逆轉速≤100轉/分，使部分熱油經常流過泵內，達到泵熱備用目的）。4,for under high temperature (above 60℃) conveying the viscosity ofoil (such as: heavy oil) of the standby pump, it must be hotstandby pump, otherwise the pump at low temperature can cause thedamage of motor overload or pump.(suggest near the exhaustnon-return valve on the tubing pump, a small return valve installedin parallel, differentiable and the backflow preventer to standbypump, the pump slow reversal, the reverse speed 100 r/min or less,often make some hot oil flows through the pump, to pump hot standbypurposes).5、輸送介質內含有機械雜質。將嚴重影響泵的運轉和降低使用壽命，因此在泵安裝前，必須仔細清除進油管內的焊渣，沙粒等雜質，并應在進油管道靠近泵處安裝濾器，濾器網孔大小，可根據工作情況及介質粘度確定。（一般可用40~80目網），過濾面積一般不得小于進油管橫截面積的20倍。5,mechanical impurity is contained within the transmissionmedium.Will seriously affect the operation and reduce the servicelife of pump, so before the pump installation, must be carefullyclean up the feed tube welding slag, impurities such as grains ofsand, and shall be installed in the inlet pipe near the pumpfilter, filter mesh size, is decided according to the workingcondition and medium viscosity.Available (40 ~ 80 mesh net), filterarea generally shall not be less than 20 times into thecross-sectional area of the tubing6、盡量在泵進油和排油口處的螺紋孔上連接壓力表和真空表，以便于觀察泵的運轉狀態。6, as far as possible inthe pump suction and discharge of oil on the threaded hole mouthconnect pressure gauge and vacuum gauge, in order to observe thepump runningstate.7、原動機與泵的轉軸必須在同一中心線上，可用直尺測隙規在聯軸器圓周上間隔90°處檢查。8、原動機與泵的轉向必須一致，嚴格禁止原動機驅動泵逆轉。電機接線時，應先脫開電機與泵的聯軸器，對電機作試運轉。使其轉向與泵的轉向標志一致。7,prime mover and the pump shaft must be in the e center line,available ruler feeler gauge in the coupling of the circumferenceof a circle by 90°in check.8, steering engine and pump must beconsistent, strictly prohibited prime motor driven pumpreversal.Electrical wiring, should first release coupling of motorand pump, a test run on the motor.The steering pump and steeringsign agreement.

 ●3G型三螺桿泵的使用

　　1、泵啟動前，必須全開進油和排油閘閥。The use of 3 g type three-screw pump1, before starting the pump, oil inlet must be fully open and oildischarge gatevalve.2、首次啟動泵或再次使用長期封存的泵時，泵內無介質，應在泵的進油腔灌注適量輸送介質，避免泵干啟動。2, start thepump for the first time or again for a long time use of the pump,the pump inside without medium, should be in the inlet of the pumpcavity perfusion amount transfer medium, avoid dry start pump3、泵啟動后，應密切注意電流表，壓力表和真空表的數值，超出規定值時，應停泵找出原因后，再行啟動。3, the pump starts,should pay close attention to current meter, pressure gauge andvacuum gauge value, beyond the specified value, should stop pumpafter find out, startagain.4、軸封處點滴泄露，應屬正?，F(xiàn)象，當泄露量大量增加時，對軟填料密封應壓緊填料壓蓋，對機械密封應停泵修復后，再行啟動。4,shaft sealing drip leakage, should belong to the normal phenomenon,when the leak amount of increase, the soft packing seal should becompression packing gland, to pump mechanical seal shall beshutdown after repair, start again.5、用高溫蒸汽清掃管線時，應避免高溫蒸汽通過泵內。5, withhigh temperature steam cleaning pipeline, should avoid hightemperature steam through thepump.6、如果泵長期不工作時，應進行油封，并定期檢查油封情況，必要時重新油封。6, if the pump is notworking for a long time, should carry on the oil seal, andregularly check oil seal, oil seal again if necessary.

 三螺桿泵  3GR85×2W21 燃油輸出 低噪音無脈動 泊頭廠家生產