XRW-300B熱變形、維卡軟化點溫度測定儀 

一  產品介紹;

  XRW-300熱變形、維卡軟化點溫度測定儀主要用于非金屬材料（如塑料、橡膠、尼龍、電絕緣材料等）的熱變形及維卡軟化點溫度的測定。具有質量穩定，操作簡單的特點，是化工企業、科研單位、大專院校等行業的理想測試工具。

工作原理

維卡（VST）定義：把試樣放在液體介質或加熱箱中，在等速升溫條件下測定標準壓針在（50+1）N力的作用下，壓入從管材或管件上切取的試樣內1mm時的溫度。

熱變形（HDT）定義：標準試樣以平放（優選）或側立方式承受三點彎曲恒定負荷，使其產生GB/T1634相關部分規定的其中一種彎曲應力，在勻速升溫條件下，測量達到與規定的彎曲應變增量相對應的標準撓度時的溫度。

二 特點:

1 試樣架為一體式結構，膨脹系數小，實驗數據真實準確。

2 采用成型單元控制器對升溫速率、溫度上限、溫度顯示進行控制。

3 操作簡單、使用方便、性能穩定。

4 顯示方式；工業觸摸屏PC機

三 符合標準；

GB/T 1633-2000(idt ISO 306:1994)維卡軟化溫度（VST）的測定
GB/T (idt ISO75-2:2003)塑料 負荷變形溫度測定（通用試驗方法）
GB/T 塑料 負荷變形溫度測定（塑料、硬橡膠和長纖維增強復合材料）
GB/T 塑料 負荷變形溫度測定（高強度熱固性層壓材料）
GB/T 8802-2001(eqv ISO 2507:1995) 熱塑性塑料管材、管件維卡軟化溫度的測定

同時符合、ISO 2507、ISO 75、ISO 306、ASTM D 1525,ASTM D 648等標準要求。

四 主要技術參數

1 溫度控制范圍：室溫～300℃；

2 升溫速率：120±10℃／h（12℃±1℃／6min ）

            50±5℃／h（5℃±0.5℃／6min）

3 變形測量范圍：變形測量范圍為0～10.000mm，變形分辨力為0.001mm，變形測量準確度0.005mm

4 試樣架數量：4個；

5 試樣跨距：64±1 mm  100±1 mm

6 Zui大加熱功率：4kw；

7 冷卻方式：自然冷卻，水循環冷卻

8 加熱介質：甲基硅油（粘度200厘斯以下,閃點300℃以上）；

9 主機電源為交流三相五線380v±10%，50Hz，5kw。具有水冷卻循環系統。

10 維卡負荷桿裝有負荷板，固定于剛性金屬架上，能在垂直方向自由移動。負載桿和金屬架構件應具有相同的膨脹系數。

11壓針頭為硬質鋼制成，長3mm，橫截面積為1.000±0.015mm2的圓柱體，壓針頭下表面應平整，垂直于負載桿的軸線，無毛刺。

12 外形尺寸為645mmx670mmx1450mm。

實現的功能:

    1、   實時顯示試驗溫度和溫度—變形曲線。

試驗過程中，通過輸入試樣的尺寸，可自動計算出試驗所須的負荷質量。

上線溫度、變形量在使用范圍內任意設定。

誤差通過軟件自動修正。

試驗曲線顏色任意設定，可以實時顯示和隱藏，并且曲線寬度粗細任意轉換。

試驗完成或達到上限溫度時，具有報警功能，并自動停止加熱。

試驗完成后，打印試驗曲線和試驗報告。查詢歷次試驗的歷史紀錄，并能重繪歷次試驗的試驗曲線。

用戶可對自己的使用軟件進行三級密碼保護。

必須使用正板軟件進行安裝，否則系統無法運行。

Xrw-300b thermal deformation, vesica softening point temperaturetester

Product introduction;

Thermal deformation and vesica softening point temperature meterare mainly used for the determination of thermal deformation ofnon-metallic materials (such as plastics, rubber, nylon, electricalinsulating materials, etc.) and the temperature of the wikasoftening point.

With the characteristics of stable and simple operation,it is an ideal testing tool for chemical enterprises, scientificresearch units and colleges and universities.

Two features:

1. The sample frame is a one-piece structure with smallexpansion coefficient, and the experimental data is accurate andaccurate.

The heating rate, temperature cap and temperature display arecontrolled by the forming element controller.

3 simple operation, convenient use and stable performance.

4 display mode;

Computer control

Three meets the standard;

GB/T 1633-2000(idt ISO 306:1994) the determination of thetemperature of the softening temperature (VST)

GB/T (idt ISO75-2:2003) plastic load deformationtemperature measurement (general test method)

GB/T plastic load deformation temperaturemeasurement (plastic, hard rubber and long fiber reinforcedcomposite)

GB/T plastic load deformation temperaturemeasurement (high strength thermosetting laminated materials)

GB/T 8802-2001(eqv ISO 2507:1995) the determination ofthermoplastic pipe and pipe - dimension card softeningtemperature

Also meet the re of ISO 2507, ISO 75, ISO 306, ASTM D1525,ASTM D 648, etc.

Main technical parameters

1 scope of temperature control: at room temperature to 300℃;

Heating rate: 120 plus or minus 10 ℃ / h (12 ℃ + / - 1 ℃ / 6min)

50 + / - 5 ℃ / h (0.5 ℃ / 5 ℃ + 6 min)

3. Deformation measurement range: the deformation measurementrange is 0 ~ 10.000 mm, the deformation resolution is 0.001mm andthe deformation measurement accuracy is 0.005mm

4 sample frame number: 3;

Sample span: 64 + 1 mm 100 mm 100 mm

Maximum heating power: 4kw;

7 cooling mode: natural cooling, water circulation cooling

8 the heating medium: methyl silicone oil (below 200 CSTviscosity, flash point above 300 ℃).

The host power supply is ac three-phase five-wire 380v plus orminus 10%, 50Hz, 5kw.

It has water cooling but circulatory system.

The 10 vicar load bar is e with a load plate, fixed on arigid metal frame, and can move freely in the verticaldirection.

The load bar and metal structure should have the same expansioncoefficient.

The pressure needle is made of hard steel, 3mm long, and thecross sectional area is 1.000 + 0.015 mm2, the surface of thepressure needle should be flat, perpendicular to the axis of theload rod, without burr.

The size of 12 is 645mmx670mmx1450mm.

Implementation functions:

1. Real-time display test temperature and temperature -deformation curve.

2. During the test, the load of the test isautomatically calculated by entering the sample size.

3. The on-line temperature and deformation are set arbitrarilywithin the range of use.

4. The error is automatically corrected by software.

5. The test curve color is arbitrary and can be displayed andhidden in real time, and the curve width is arbitrarilyconverted.

6. When the test completes or reaches the upper limittemperature, it has alarm function and automatically stopsheating.

7. After completion of the test, print test curve and testreport.

Check the historical records of the previous experiments and canredraw the test curves of the previous experiments.

8. Users can make use of their own software for three-levelpassword protection.

9. You must use the positive board software for installation,otherwise the system will not work.