公司已通過ISO9001：2000國際質量體系認證，中國船級社CCS型式認證，法國船級社BV產品工廠認證，美國船級社ABS產品質量認證，成為中石油物資資源市場成員、中石化物資資源市場成員，并列入《武器裝備科研生產保密資格名錄》可以承擔軍隊系統裝備部門的涉密武器裝備科研生產合同項目。河北省知名產品生產企業，船用泵產品承制企業。

     主機燃油駁運泵通過多國船級社認證;KCB55(2CY3.3/0.33)流量:3.3m3/h壓力:0.33Mpa口徑:G1",配電機Y90L4

      ●KCB齒輪泵性能范圍

　　主要用于油田、油庫、港口、碼頭、船舶等大流量輸油，卸油

　　應用范圍:KCB/2CY型齒輪輸油泵適用于輸送粘度在300c.s.t以下的各種油類，如原油、柴油、潤滑油、動植物油等。配用銅齒輪可輸送低閃點液體，如汽油、苯等。介質溫度不超過70℃，耐高溫油泵的使用溫度不超過300℃。本泵身帶有安全閥，超載時起安全作用。軸封有骨架油封、機械密封、填料密封三種型式，訂貨注明。KCB齒輪潤滑泵主要用于各種機械設備中的潤滑系統中輸送潤滑油，適用于輸送粘度在10oE（75c.s.t）以下，溫度在300℃以下的具有潤滑性的油料，不銹鋼齒輪泵可輸送食用油料、飲料等。軸封有骨架油封、機械密封、填料密封三種型式.

 ●KCB齒輪泵安裝說明:KCB gear pump installation instructions:

　　1、安裝泵的地點應足夠?qū)挸?，以方便檢修工作。1, thelocation of the installation of pump should be spacious enough, tofacilitate maintenance and repair work. The stand or fall of2、泵安裝的好壞，對泵的平穩運行和使用壽命有很重要的影響，所以安裝校正工作必須仔細地進行，不得草率行事。2,pump installation, for the smooth running of the pump and servicelife have very important influence, so the installation calibrationwork must be carried out carefully and must not be too hasty.3、泵吸入管的安裝高度、長度和管徑應滿足計算值，力求簡短，減少不必要的損失（如彎頭等）；并保證泵在工作時，不超過其允許汽蝕余量。4、吸入和排出管路應該有支架。泵不允許承受管路的負荷。3,installation height of pump suction pipe, the length and diametershould satisfy the calculated value, to short, reduce unnecessarylosses, such as elbow, etc.); And ensure the pump at work, no morethan the allowed NPSH. 4, suction and discharge line should be asupport. Pump are not allowed to bear load of pipeline.

●kcb齒輪泵安裝: KCB gear pumpinstallation:

　　1、泵安裝前應檢查泵和電機在運輸過程中是否受到損壞，如電機是否受潮，泵的進出口防塵蓋是否損壞而使污物進入泵腔內等。1,before the pump installation, should check the pump and motor isdamaged during the transit, whether be affected with damp beaffected with damp such as motor, pump the import and export ofdust cover for damage and make the dirt into the pump chamber,etc.

　　2、泵在搬運過程中，應選擇合適起吊位置，減少泵的變形。2,pump in the process of handling, should choose appropriate liftingposition, reduce the deformation of the pump.

　　3、泵的底座應固定在牢固的基礎上，以免產生振動影響泵的正常工作。3, the base of the pump should be fixed on the basis of thestrong, so as to avoid vibration influence the normal work of thepump.

　　4、泵的進出口管路應清理干凈不得存有硬顆粒的報告雜物。4,import and export of pipeline of pump should be cleaned up shallnot have the report of hard particles sundry.

　　5、管路口徑一般不小于泵的進出口徑，進油管路應盡量短，并減少彎路。必要時在進油口安裝金屬過濾器，過濾器的有效面積不應小于管道過流面積的三倍。5,pipe diameter is generally not less than the in and out of thecaliber of pump, the oil pipeline should be short, as far aspossible and less detours.When necessary, metal filter is installedon oil inlet filter effective area should not be less than threetimes of pipe flow area.

　　6、安裝時，不得用泵來承擔管路的重量。7、用手轉動聯軸器，泵應轉動靈活，不得有過緊或輕重不均現象，如有應立即排除。

6, when installation,must not use the pump to bear the weight of the line.7, turn thecoupling with the hand, the pump should be flexible rotation, cannot have too tight or weight uneven phenomenon, should immediatelyruled out.