火熱銷售油脂加注泵KCB33.3齒輪泵

●KCB齒輪泵性能范圍

　　主要用于油田、油庫、港口、碼頭、船舶等大流量輸油，卸油

　　應用范圍:KCB/2CY型齒輪輸油泵適用于輸送粘度在300c.s.t以下的各種油類，如原油、柴油、潤滑油、動植物油等。配用銅齒輪可輸送低閃點液體，如汽油、苯等。介質溫度不超過70℃，耐高溫油泵的使用溫度不超過300℃。本泵身帶有安全閥，超載時起安全作用。軸封有骨架油封、機械密封、填料密封三種型式，訂貨注明。KCB齒輪潤滑泵主要用于各種機械設備中的潤滑系統中輸送潤滑油，適用于輸送粘度在10oE（75c.s.t）以下，溫度在300℃以下的具有潤滑性的油料，不銹鋼齒輪泵可輸送食用油料、飲料等。軸封有骨架油封、機械密封、填料密封三種型式.

 ●KCB齒輪泵安裝說明:KCB gear pump installation instructions:

　　1、安裝泵的地點應足夠?qū)挸?，以方便檢修工作。1, thelocation of the installation of pump should be spacious enough, tofacilitate maintenance and repair work. The stand or fall of2、泵安裝的好壞，對泵的平穩運行和使用壽命有很重要的影響，所以安裝校正工作必須仔細地進行，不得草率行事。2,pump installation, for the smooth running of the pump and servicelife have very important influence, so the installation calibrationwork must be carried out carefully and must not be too hasty.3、泵吸入管的安裝高度、長度和管徑應滿足計算值，力求簡短，減少不必要的損失（如彎頭等）；并保證泵在工作時，不超過其允許汽蝕余量。4、吸入和排出管路應該有支架。泵不允許承受管路的負荷。3,installation height of pump suction pipe, the length and diametershould satisfy the calculated value, to short, reduce unnecessarylosses, such as elbow, etc.); And ensure the pump at work, no morethan the allowed NPSH. 4, suction and discharge line should be asupport. Pump are not allowed to bear load of pipeline.

●kcb齒輪泵安裝: KCB gear pumpinstallation:

　　1、泵安裝前應檢查泵和電機在運輸過程中是否受到損壞，如電機是否受潮，泵的進出口防塵蓋是否損壞而使污物進入泵腔內等。1,before the pump installation, should check the pump and motor isdamaged during the transit, whether be affected with damp beaffected with damp such as motor, pump the import and export ofdust cover for damage and make the dirt into the pump chamber,etc.

　　2、泵在搬運過程中，應選擇合適起吊位置，減少泵的變形。2,pump in the process of handling, should choose appropriate liftingposition, reduce the deformation of the pump.

　　3、泵的底座應固定在牢固的基礎上，以免產生振動影響泵的正常工作。3, the base of the pump should be fixed on the basis of thestrong, so as to avoid vibration influence the normal work of thepump.

　　4、泵的進出口管路應清理干凈不得存有硬顆粒的報告雜物。4,import and export of pipeline of pump should be cleaned up shallnot have the report of hard particles sundry.

　　5、管路口徑一般不小于泵的進出口徑，進油管路應盡量短，并減少?gòu)澛贰１匾獣r(shí)在進油口安裝金屬過濾器，過濾器的有效面積不應小于管道過流面積的三倍。5,pipe diameter is generally not less than the in and out of thecaliber of pump, the oil pipeline should be short, as far aspossible and less detours.When necessary, metal filter is installedon oil inlet filter effective area should not be less than threetimes of pipe flow area.

　　6、安裝時，不得用泵來承擔管路的重量。7、用手轉動聯軸器，泵應轉動靈活，不得有過緊或輕重不均現象，如有應立即排除。

6, when installation,must not use the pump to bear the weight of the line.7, turn thecoupling with the hand, the pump should be flexible rotation, cannot have too tight or weight uneven phenomenon, should immediatelyruled out.

 

●KCB齒輪泵概述

　　KCB齒輪油泵在輸油系統中可用作傳輸、增壓泵；KCB gearoil pump in the oil system can be used as a transport, boosterpump;

  在燃油系統中可用作輸送、加壓、噴射的燃油泵；In the fuel system can beused as a transport, pressure, jet fuel pump;

  在一切工業領域中，均可作潤滑油泵用。In all industrial areas, canbe used as lubricating oil pump.

輸送污水泵G25-1V-W102不銹鋼單螺桿泵中藍國際有限公司輸送稠油泵G135-1P-W101單螺桿泵青島海晶集團有限公司油脂加注泵W6.4Zi62Z1M1W73上海國際油漆有限公司輸送膏狀物泵NYP110-RU-T2-J-W11保溫高粘度泵中國阿拉伯化肥有限公司輸送乳狀液泵NYP110-RU-T2-J-W12高粘度保溫深圳諾普信農化股份有限公司輸送水煤漿泵W6.4ZK-62M1W73鄂爾多斯電力冶金股份氯堿有限公司輸送涂料泵G40-1P-W101單螺桿泵浙江三美股份有限公司輸送基礎油泵YCB2.5齒輪泵江蘇常隆有限公司輸送齒輪油泵YCB5齒輪泵浙江天和樹脂有限公司輸送潤滑脂泵YCB8齒輪泵山東東佳集團公司油脂加注泵KCB83.3齒輪泵上海泰禾有限公司輸送橄欖油泵W6.4ZK-100Z3M1W7內蒙古蘭太實業股份有限公司輸送柴油降凝劑泵G40-1P-W101單螺桿泵中鹽吉蘭泰集團有限公司輸送耐磨液壓油泵YCB10齒輪泵江蘇綠陵集團有限公司油脂加注泵KCB300齒輪泵山東聯合股份有限公司輸送SBS瀝青改性劑泵NYP110保溫高粘度泵遼寧呂氏（集團）有限公司輸送乳化瀝青泵NYP110保溫高粘度泵浙江大東南塑膠集團公司輸送改性瀝青泵NYP110保溫高粘度泵江蘇省新世紀鹽化集團有限責任公司油脂加注泵NYP110不銹鋼保溫高粘度泵湖南海利高薪技術產業集團有限公司輸送灌封膠泵NYP110不銹鋼保溫高粘度泵山東齊旺達集團海仲石化有限公司輸送粘膠劑泵NYP110不銹鋼高粘度泵杭州之江有機硅有限公司輸送再生泡沫泵NYP220B-RU-T1-J-W12高粘度泵 帝人聚碳酸脂有限公司輸送復合膜膠粘劑泵NYP220B高粘度泵甘肅金昌工業集團有限公司輸送汽輪機油泵YCB20齒輪泵華能南通電廠輸送燃料油泵3GCLS100*2W2三螺桿泵南通港閘船舶制造有限公司

  KCB齒輪泵主要有齒輪、軸、泵體、安全閥、軸端密封所組成。齒輪經熱處理有較高的硬度和強度，與軸一同安裝在可更換的軸套內運轉。泵內全部零件的潤滑均在泵工作時利用輸出介質而自動達到。KCBgear pump are mainly gear, shaft, pump body, valve, shaft end seal.Gear after heat treatment with high hardness and strength, andshaft installed in the replaceable shaft sleeve. In all parts ofthe lubrication pump are pump work automatically to achieve usingthe output media.

  泵內有設計合理的泄油和回油槽，是齒輪在工作中承受的扭矩力Zui小，因此軸承負荷小，磨損小，泵效率高。Pump is the drainage and back into the groove of reasonabledesign, is a gear in the work under the minimum torque force, sothe bearing load is small, wear small, pump with highefficiency.

 

  泵設有安全閥作為超載保護，安全閥的全回流壓力為泵額定排除壓力的1.5倍，也可在允許排出壓力范圍內根據實際需要另外調整。但注意本安全閥不能作減壓閥的長期工作，需要時可在管路上另行安裝。從主軸外伸端向泵看，為順時針旋轉。Pumpis e with safety valve as overload protection, the totalreflux pressure relief valve is rated pump out pressure of 1.5times, also can allow discharge pressure range according to actualneeds and adjust. But note that this cannot be a long-term workpressure reducing valve, relief valve can be installed in thepiping shall be separately when necessary. To pump from the mainshaft overhang end to see, for clockwise.