Plug and Drive NitroOBD2 Performance Chip Tuning Box for BenzineCars

ID NO.:CTE038

Plug and Drive NitroOBD2 Chip Tuning Box for BenzineCars

35% More Power, 25% More torque

NitroOBD2 is a Plug&Drive Ready device to function theincreasing the performance of engine.

NitroOBD2 is easy to install. Just plug it into the OBD2 connectorof cars. NitroOBD2 fits all car from the year of 1996.

Plug and Drive NitroOBD2 Performance Chip Tuning Box for BenzineCars

NitroOBD2 Chip Tuning Box works based OBD2 protocols as remapingthe Car's computer ECU. After driving 200 km road total, NitroOBD2adjusts itself to the car, according to the drivers' habits andalways keeps remaping the ECU to increase the performance ofengine.

What does NitroOBD2 make?

According to your driving habits,  NitroOBD2 makes new map inthe car's computer ECU to increase the performance of your car. Asyou driving much more KM/Mile, it renews the map. Thus it keeps thevehicle's power and torque increasing.

What is NitroOBD2 Chip Tuning Box?

NitroOBD2 is a Chip Tuning Box which can be plugged into OBD2connector of your car to increase the performance of yourcar.

When it plugged into OBD2 connector, NitroOBD2 receives theinformation from the car computer ECU. With the received data fromECU,

NitroOBD2 adjusts the boost pressure, of fuel, injectiontiming and pressure to increase the performance of yourcar.

NitroOBD2 Chip Tuning Box does not exceed the manufacturerre It works only within the tolerance of theengine.

NitroOBD2 finds out the hidden power of your car. NitroOBD2 doesnot damage the engine and the car computer ECU or not cause anynegative effects to the car factory setting.

NitroOBD2 does not change any of the settings permanently. To turnback to the car's original settings, just unplug NitroOBD2 fromOBD2 connector.

NitroOBD2 finds out the hidden power of your car.

- Up to 35% more power

- Up to 25 % more torque

NitroOBD2 is very easy to use.

Plug NitroOBD2 into OBD2 connector of your car. And turn theignition on for 30 seconds. And Turn the engine on.

NitroOBD2 settings are optimal and the best for your car. Even theparameters are different for each vehicle,

there might not be a need to make an additional adjustment.NitroOBD2 will recognize your vehicle and your driving habits afteraround 200 km/150 miles driving,

and then NitroOBD2 adjusts itself to match your carperfectly.

NitroOBD2 works on the basis of changing the signal form ECU. Asuence, it changes the whole injection map.

The main difference between NitroOBD2 Chip Tuning Box and Remappingtuning methods is that NitroOBD2 Chip Tuning Box is easilyremovable,

and after unplug you go back to the factory settings. EcoOBD2 isthe cheap and safe type of tuning.

Remapping is a permanent change to your car. This is the expensivetuning and you cannot remove it.

NitroOBD2 is e with the engine protection function and safe for your car engine.

NitroOBD2 produced on the printed circuit board in SMD technology.NitroOBD2 Chip Tuning Boxes are high

Installation and Calibration

1* Pull the Car Key out from the ignition.

2* Find OBD2 connector(*) in your car and Plug in NitroOBD2 ChipTuning Box

3* Insert the key into the ignition and twist the key to the firststage. (Do not start the car)

4* Press the reset buttom for about 5 sec. After releasing thebuttom, just wait for a while about 30-54 sec. (NitroOBD2 ChipTuning Box will communicate and establish connection withECU)

5* Start up the engine.

6* NitroOBD2 Chip Tuning Box will recognize your vehicle and yourdriving habits, after around 200 km/150 miles driving and thusNitroOBD2 Chip Tuning Box will adjust itself to match your carperfectly for more fuel saving.

Each device available for LPG.

Does your car have OBD2 connector?

On-Board Diagnostics, or "OBD," is a computer-based system builtinto all 1996 and later light-duty vehicles and trucks, as re the Clean Air Act Amendments of 1990.

OBD systems are designed to monitor the performance of some of anengine's major components including those responsible forcontrolling emissions.

OBD2 necessarily for cars:

- Sold after January 1, 1996 in the USA

- Sold after January 1, 2001 in the European Union

- With diesel engine sold after January 1, 2003

Where located OBD2 connector in your car?

1 Driver's side, underneath dasboard, in the area under thesteering column,

2 Driver's side, underneath dasboard,between the driver-side doorand steering column area

3 Driver's side, underneath dasboard, between the steering columnarea and the center console

4 Driver's side, dashboard instrument/gauge area, between thesteering column and center console

5 Driver's side, dashboard instrument/gauge area, between thedriver-side door and steering column

6 Center console, vertical surface  left of vehiclecenterline

7 Center console, vertical surface right of vehicle centerline oron passenger side of center console

8 Center console, horizontal surface  in front passengerarea.

Package content:

1pc x NitroOBD2 Chip Tuning Box Interface

1pc x User Manuel English