ft-dx3000d是yaesu ftdx系列Zui新的一份子。它從倍受贊譽的ft-dx9000和ft-dx5000收發信機繼承來的設計理念，能夠在嘈雜的頻段上提供與dx5000十分接近的多信號接收特性。以10khz為間隔的雙信號動態范圍測試中，ft-dx3000能達到108.5db的出色表現，ip3為 +37dbm；把信號間隔縮小到2khz，其動態范圍也有106 db，ip3 +33dbm。如此性能是業余短波通信設備中當之無愧的佼佼者。

其他的亮點功能還有：

重量只有10公斤不到

100w，內置天調

30khz-56mhz連續接收

內置rtty/psk31編解碼

9mhz中頻輸出，便于外接頻譜、sdr等

直接usb端口實現固件更新、cat設備控制、音頻輸入輸出和ptt控制

高亮度、寬視角的4.3英寸彩色tft液晶屏，帶高速頻譜

高性能射頻前端，帶15個帶通濾波器

下變頻的接收機，帶有3khz修平濾波器用于ssb以及300hz（選件）和600hz修平濾波器用于cw。

32位中頻dsp，采用300mh主頻的titms320c6727b芯片，提供各種中頻帶寬的調整和降噪功能。

高穩定度、高度的40mhz tcxo(0.5ppm)及其dds電路為設備提供了精準的基準頻率，并直接鎖定pll和vco，帶來高質量的本地信號和信噪比性能。這意味著接收機的噪音門限很低，并能提供的2khzip3阻塞動態范圍。

帶均衡器的麥克風放大器

中頻dsp語音處理器，增強話音頻譜的功率，并減少其他的成份，從而讓你的語音在競賽或追求dx的過程中更具穿透力。

3個天線座

 

 160 through 6 meters -ssb/cw/fm/am/digitalwith efficient dimensions of14.4" x 4.5" x 12.3" (w x h x d) and weighing in at only 22 pounds,the ft dx 3000d is a solidly packed tranceiver ready to give veryhigh performance on all amateur radio bands from 160 to 6meters. 
? general coverage reception from 30 khz to 56 mhz 
? fm & am - wide and narrow modes includedrtty/psk31 encode / decodeincludedvarious easy connections available for rtty,sstv, psk31, jt, and other digital modes100 watts of solid performancetherf final amplifier produces a clean 100 watt (some modesless)transmit signal. a large heat sink is combined with the diecast aluminum chassis for efficient heat dissipation. a cooling fanlocated beside the final amplifier and the tx low pass filterventilates the heat away from inside of the transceiver cabinet.this large axial flow fan is mechanically isolated from the chassisto reduce vibration and noise. the speed of the fan is continuouslycontrolled by the temperature of the pa amplifier; starting at 40degree c.antenna tunerincludedhigh speed automatic antenna tuner included.the antenna tuner uses lc switching. it has a large capacity 100channel memory; the tuning data is automatically memorized toreduce tuning time when changing fre yaesu main tuning knobaheavy weighted balanced brass core knob is used to give the famousyaesu smooth flywheel operating feel to the ft dx 3000d main dialknob. each user may set his/her favorite torque feeling of the maindial rotation.ifoutput1st if 9mhz signal with wide bandwidth ifoutput available on the rear panel for after-market band scopes, cwskimmer, etc.usbcapableusb input included for firmware updates. thisinput can also facilitates cat, usb audio in / out and usb txcontrol (ptt, key and fsk)remote control from a distantlocationexternal control (cat) is possible using usbor serial port; this feature means the ft dx 3000d can be remotetlycontrolled from a distant location!big tft full-color display for superioroperability and visibilitythe ft dx 3000d presents awide view angle, high contrast lcd 4.3 inch tft impressive fullcolor display that provides a convenient view of the radio’sworking functions. superior operability is realized with thisconvenient display. it permits excellent visibility from differentviewpoints. even with the many ft dx 3000d features and functions,the tft display makes operation of the radio easy andcomfortable. 
? a block diagram displays rx signal path 
? choose analog type or bar graph meter 
? selectable analog type or bar graph type meterindication 
? separate independent frequency display 
? high speed spectrum scope 
? bandwidth of the spectrum scope: 20khz, 50khz, 100khz, 200khz,500khz, or 1mhz 
? tx and rx markers appear during “spit” operation 
? level indicator 
the function names and the setting levels of the followingfunctions are shown in the tft main display when a function knob isrotated: clarifier, microphone gain, speech processor, shift,width, keyer speed and contour 
? af-fft scope 
an af-fft (audio frequency fast fourier transform) scope is builtin. this af-fft function was first demonstrated in the ft dx 9000series. with this scope, the audio characteristics of the receivedsignals; the effect of adjusting the rx if filter performance; andutilizing the qrm rejection features, may be visually observed. itis also possible to observe the tx audio characteristics of yourown signal while using the monitor function. this is very effectivefor tuning the parametric e for voice characteristics andthe microphone audio. 
? spectrum scope memory 
the spectrum scope screen can be stored or recalled with one touch.simultaneously the time information is recorded in the memory, sothat the difference in activity may be reviewed and compared,depending on the seasons and times. 
? cursor keys 
six keys that are used fre in normal operation are locatedat the left side of the tft display. other functions can beoperated by pressing the "scope" key which changes the "spectrumscope screen" to "function key display screen". even if the radiois turned off, the last operated key function is memorized andhighlighted.top performingrf front endthe rf front end circuit is the mostimportant element because it ultimately determines the hf receiverperformance. our yaesu engineering team has concentrated superiorrf engineering knowledge into the design of the ft dx 3000d frontend. 
? fifteen separate band pass filters (bpf) are used for front endprotection. this effectively reduces the undesired and out of bandsignals. 
? in the rf amplifier, the strong bipolar transistor (2sc3357) isused. this transistor shows a low nf, and provides superiorintermodulation performance. 
? the gain of each individual device is kept lower, and the bestoptimized working point, with the lowest nf, is selected. 
? a custom-designed wide coverage transformer, with less magneticsaturation, is used for the i/o of the rf amplifier. thisconstruction makes the device performance better and providesexcellent multi signal performance.down conversion receiver and powerful narrowbandwidth crystal roofing filtersthe powerful narrowbandwidth crystal roofing filter enhances the receiver multi-signalcharacteristics. the ft dx 3000d "down conversion" receiverconstruction is similar to the ft dx 5000. the first if fre 9 mhz. this makes possible narrow bandwidth crystal roofingfilters (300 hz, 600 hz or 3 khz) with a sharp shape factor thatcreates amazing multi-signal receiving performance. the powerfulnarrow bandwidth crystal roofing filter enhances the receivermulti-signal characteristics. 
? the 3 khz roofing filter greatly improves ssb signal receptionduring close adjacent multi signal conditions. 
? the 300 hz* and 600 hz roofing filters provide the best cwreceiving environment when the adjacent signals may affect thedesired signal reception. 
*note: 300 hz filter orm and tive qrm rejection is achieved fromthe ft dx 3000d if dsp. the 32-bit high speed floating decimalpoint dsp, tms320c6727b (maximum 2800 mips/ 2100 mflops) made bytexas instruments, is used for the if section of the ft dx 3000d.the signal is processed with the high speed 300 mhz clockfre 
? proven if width and if shift functions provide great performance 
if shift 
with the normal bandwidth, the pass band area can be movedrelatively, so that harmful signals are rejected from the passband 
if width 
by adjusting the band width, interfering signals can be removedfrom both sides of the pass band, without changing the pass bandposition. the if width function can make the pass band narrowerwith one-touch. this function is effective in a pile-up or contest,when the undesired signals are located just above and below thetarget signal. when the if width knob is centered (click point),the pass band width is 2.4 khz in the ssb and cw modes. when “nar”is turned on, the minimum pass band becomes 50 hz (200 hz in thessb mode), making it possible to minimize the qrm with this sharpfilter shape factor. when the if width is turned clockwise from thecenter click point, the pass band width can be extended wider, upto 4000 hz. this may provide a richer sounding and moreso when in a local rag chew. 
? contour 
the contour function ideally tailors the received audio signalwithout changing the bandwidth. the contour function varies theoutline of the if dsp filter pass band characteristics, and thein-band signal construction can be partially altered. differentfrom the if shift or if width, the special contour pass band, canreduce or peak the desired signal, partially and continuouslyacross the pass band. this feature is effective especially when theundesired signal is close to the center fre 
? digital noise reduction (dnr) by dsp 
the installed digital noise reduction circuit provides 15 separateparameters. the noise reduction constants may be set to the optimalworking point by varying the 15 step parameters according to theactual noise within the hf band. the desired signal components arepeaked and the random noise components are effectivelycancelled. 
? if notch 
this high has steep attenuation characteristics of 70dbor more. effective removal of a strong beat signal is obtained. thedamping characteristics can be switched to wide or narrow bandwidth, and the attenuation level may be adjusted in the settingmode menu. interfering signals may be attenuated, while minimizingthe impact on the received signal. 
? digital notch filter (dnf) (auto notch) 
the digital notch filer (dnf) is a feature that automaticallyfollows the interfering heterodyne signals, even if there are morethan one, and even if the beat frequency changes with time. this iseffective in removing jamming signals. 
? cw apf (audio peak filter) 
in the cw mode, the apf (audio peak filter) function has an audiopeak at the signal frequency; this improves the s/n and increasesthe readability of the cw signal. the apf peak frequency can befinely aligned.very lownoise floor - terrific signal to noise ratiothe s/nratio (signal-to-noise ratio) of the local signal that is injectedinto the 1st if mixer is one of the most important factors forimproving the receiver properties in the ultra-multi-signalenvironment. 
in the ft dx 3000d, the combination of it's high stability and highaccuracy 40 mhz tcxo (± 0.5ppm, -10 °c ~ +60 °c), and it's ddscreate the fundamental frequency of this radio, and is locked tothe pll-ic and vco directly. this circuit construction and methodcreates the highest local signal, with superior s/nperformance. this means the receiver noise floor is kept lower, andrealizes the best blocking dynamic range at 2 khz ip3performance.three iposettings - best signal reception during changing bandconditions3-step ipo settings permit the operator toselect the most appropriate gain for best signal reception. thisvariety of selections provides superior receiver performance andthe best possible communications with changing bandconditions. 
the ipo (intercept point optimization) is selected by a controlswitch located on the front panel. the ipo selection determines thegain of the rf amplifier. the gain setting is very effective inoptimizing the receiver performance, depending on the antenna andthe communication propagation conditions. the ipo, the att and onestage of the rf amplifier are used to optimize the signal levelsthat are sent to the mixer. this is especially important for hflow-band operation. the "amp 1" uses one rf amplifier stage, andmaintains a better balance between the sensitivity and the receiverperformance (the gain is around 10 db). in addition, "amp 2" usestwo stages of the rf amplification and can obtain highersensitivity (the gain is around 17 db); something particularlyimportant on the 6 and 10 meter bands.high audiowith punchthe modulation circuit ofthe ft dx 3000d utilizes digital variation operational modulation,which creates ideal high transmission audio. 
? microphone amplifier that includes parametric e 
the modulation circuit of the ft dx 3000d utilizes the digitalvariation operational modulation type, which creates ideal high transmission audio. this radio has a parametric ethat makes possible versatile adjustment of the tx audio byaligning the tx band audio spectrum. the parametric e canalter the low, mid and high part of the audio separately. thisthree stage parametric e can generate high tx audiosound because it can be tuned in detail…without sacrificing theaudio dignity. 
? if dsp speech processor – dx’er and contester proven 
the ssb speech processor uses if digital signal processing toincrease the intelligibility of the transmitted signal during weaksignal crowded conditions. the dsp increases the average power ofthe important speech spectrum components and reduces the tx powerof the less significant components. adjust the compression level inthe menu mode to adapt the transmitted ssb signal to best suiteyour voice characteristics, the situation, propagation conditionsand pile-up demands.threeantenna inputsthree antenna connectors are availableon the ft dx 3000d rear panel. 
? having multiple antenna selections is an especially effectivefeature for dx and contest operating. 
? antenna connection selections memorized and recalled whenchanging bands. 
? the "ant 3" input can be set for the "rx only"antenna.cw featuresgalore? cw apf (receiver audio peak filter) with 3bandwidth steps 
? cw decode included 
? cw spot 
? cw auto zero-in 
? cw zero-in display 
? cw full break-in 
? cw mode reversal (usb or lsb) 
? cw keying available during ssb operation 
? cw “vox” delay is adjustabe 
? electronic keyer with weight control 
? keyer paddle dot-dash reversal 
? iambic a/b selection 
? “bug” keying emulation 
? four message memory (50 characters each); five w/fh-2keypad 
? automatic insertion of incrementing contest number 
? automatic “beacon” keyer mode 
? dial step setting (for the cw mode only) 
? separate key jacks on the front and rearpanels5 digital voicemessageseach memory channel is capable of storing upto 20 seconds of audio using the optionaldvs-6.rxoutputthe "rx output" connector on the ft dx 3000drear panel accesses the signal from the receiver rf amplifier. thesignal can then be output to an external receiver for in-bandsimultaneous receiving.optional fully-automatic μ-tuningkitthe u-tuning kit that was developed for the ft dx9000, is optionally available for use with the ft dx 3000d. noother amateur radio radio manufacturer offers a comparable devicethat may improve your dxing performance in some challengingoperating situations. 
a large diameter 28 mm inductor, with an adjustable ferritemagnetic material (ni-zn ferrite) core, is combined, with a highresolution and high torque stepping motor to automatically find theresonance point. by inserting these tuning units prior to the rffront end of the receiver, the ip3 points are improved by around 4db. three individual tuning units are available coveringfre from 1.8 mhz through 14 mhz. many ft 950, ft 2000/d, ftdx 5000 and ft dx 9000 yaesu customers have used them and foundthem especially effective for use on the lower bands.

相關其它產品：

本產品的種類是整機，品牌是YAESU，型號是FT-DX3000，類型是專業級，類別是車載臺，頻率范圍是30-56（MHz），射頻輸出功率是100（W），理論通訊距離是50（km），工作電壓是13.8（V），電池類型是30A電源，監聽功能是有，重量是5000（g）