小圓開關---五檔雙座分控

一.組成:

由四片熱片,一條帶開關和控制器的線纜組成.

二.安裝:

1．先將座套取下來,而后將四片加熱片分別固定在座和靠背上.

2．當把座和靠背的熱片裝好后,將熱片上的電極引出線從座和靠背的中縫穿于座椅下面,再與線纜上插件對插.

3．將帶控制器的線纜平鋪于地腳下面.線纜上的紅,黑,兩條線待五檔控溫開關安裝好后再與汽車電源連接.

4．五檔開關的安裝:在汽車音響的下方與手剎的前方之間,找一個適當?shù)奈恢?開一個與開關大小直徑相當?shù)目?注意孔的直徑不要大于開關的直徑,否則開關會松東,如果開關松動,當開關裝好后,在開關和孔的邊緣之間點一些502膠,不要點太多.

5．開關安裝好后,將開關上的四芯插件與線纜上的四芯插件對插.

6．完成以上步驟后,這時候可以接電源了.首先將黑色線接到搭鐵線上,如鑼母與車體相連的地方,或座椅與車體相連的地方.如鑼母上有漆料,應先把其剝離掉,而后將黑線壓牢擰緊于此處.否則會接觸不良影響使用.這時候可以接紅線了,首先在儀表盤下面的配線部分,找到一條平時通過10安以上電流的線,當汽車熄滅后,這條線上電流應為零.線徑在1.5毫米以上.也可以將紅線壓在標有10a以上的保險管座的下面.這條線尋找的方法:將萬用表檔位打到直流電壓20v的地方,打開萬用表電源開關,將黑表筆與搭鐵線相接觸,紅表筆與要找的那一點相接觸,當汽車啟動后,這點有12v以上的電壓,汽車熄火后,這點上沒有電壓.說明這條線找到了.否則用此法繼續找.找到后將紅線壓緊接牢.這時可以試用了.

7．需要注意的地方是:熱片里的黑色碳纖維絲不要與座椅上的金屬部分碰到一起。如金屬拉環，固定座椅上海棉用的金屬拉筋等。如果熱片開孔時，黑色碳纖維外露了，這時可用單面膠帶或膠布將其與金屬部分隔開。

三．使用方法：

1．汽車啟動后，這時可以試用了?？販亻_關分五檔控制，控制溫度分別為：華氏溫度下，123.8度，116.6度，109.4度，104度,96.8度。如果以攝氏溫度為單位，五檔控制的溫度分別為：51度，47度，43度，40度，36度。

2．利用一個五檔開關能控制雙座，也能控制單座。方法非常簡單。

3．如果出行的車上只有駕駛員一人，這時候只需主駕駛座椅加熱就可以了。第一次按動開關黃燈亮，第二次按動開關紅燈亮，第三次按動開關綠燈亮，第四次按動開關紅燈閃，第五次按動開關綠燈閃，第六次按動開關是把加熱關掉，燈滅。以上六步可把加熱溫度分別設定在六個不同溫度點。由高到低。冬季的早晨或冬天第一次啟動汽車時，汽車啟動后，按一下開關，這時黃燈亮，表示加熱溫度設定在Zui高檔，即攝氏溫度51度，當座椅被加熱后，駕駛員覺得溫度太高了，這時可第二次按動一下開關，把溫度設定在次高檔。依此類推。當?shù)谝淮伟炎窝杆偌訙睾?，根?jù)個人對溫度的敏感程度，調到適應個人的檔位即可。

4．如果副座在冬季時也有人乘坐，這時候需要把主座,副座加熱同時打開。方法是，按住加熱開關3秒后松開,這時候加熱設定開關上黃色指示燈快速閃動幾次,說明副駕駛座椅開始被加熱.其加熱溫度隨主駕駛座椅加熱溫度而變化.如果副駕駛乘座人是中途上的車,這時候駕駛員只需按住加熱開關3秒以上松開,加熱開關上黃色指示燈同樣快速閃動幾次,表示副座開始加熱,在短時間內快速追上主座溫度,而后隨主座的溫度變化而變化,隨主座的溫度設定而設定.也就是說:無論副座的乘坐人是與駕駛員同時上車還是中途上車讓副座椅加熱的方式是一樣的.

5.關掉座椅加熱的方法有兩種:無論單座還是雙座加熱,只要停車熄滅后,加熱座椅都被關掉.在行駛過程中如果只有主駕駛加熱,這時候把開關按到單支綠燈閃,而后再按一次,即可關斷主座加熱.一般調到第五檔維持加熱,不用關斷加熱.在行駛過程中,如果關斷兩個座的加熱,有兩種方法,一是與單座加熱關斷方法相同,二是按住開關3秒以上,松手后無指示燈指示時,表示雙座加熱被關斷.

1 composition

four heating pads,and a wire with a controller.

2 installation

(1)first,take off the suit of the seat,then put thepads on the back and bottom of the seat,make them durable.

(2)connect the plugins of the pads with thecontroller under the seat after the pads are ready.

(3)put the wire at the corner of theground,connnect the switch first then connect the red line andblack line and yellow line to the power supply.

(4)find a proper place between speaker andhandbrake,make a hole,the diameter of the hole could not be biggerthan the diameter of the switch,if not the may be not stable,youcan put some glue in the hole to make it stable.

(5)after the switch is ready,connect the switch tothe four core plug-ins of the wire.

(6)you can connect to the power supplynow.first,connect the black line to the ground line,if there is ascrew nut on the car and there is paint on it,you should cut offthe paint first then connect the black line under the nut,it willbe poor contact if you do not cut off the paint.then you canconnnect the red line,find a line which can transmit at least 10acurrent under the dashboard,when the car is not working thereshould be no current,you can also connect to the fuse which cantransmit at least 10a current and the diameter is at least1.5mm.how to find the line,use a multimeter to test,when the car isworking there should be at least 12v,when the car is not workingthere should be no voltage.connect the yellow line to theon-line.

(7)some point to pay attention:the carbon fiber inthe pads should not meet the metal part,you can use mackintosh toseparate them.

3 how to use

(1)there are five levels of the switch:51 degreescelsius(123.8 fahrenheit) 47 degrees celsius(116.6 fahrenheit) 43degrees celsius(109.4 fahrenheit) 40 degrees celsius(104fahrenheit) 36 degrees celsius(96.8 fahrenheit).

(2)one switch could controll two seats.

(3)if there is only one person in the car,then onlythe driver"s is working.press one time the red light is up,pressthe second time the yellow light is up,for the third time the greenlight is up,for the fourth time the red light is flashing,for thefifth time the green light flashing,for the sixth time it will beturned off and the light is off.these six level means sixtemperature,from high to low.when you are first time to start thecar in the morning,press the button once,the red light is up meansthe higheas level,if you feel it is too hot you can choose a properlevel.

(4)if you want the two seats working just press thebutton for three seconds,the yellow light will flash for coupletimes,that means the co-pilot"s seat is start to heat too,thetemperature is the same with the driver"s seat.if someone is midwayaboard,just press the button for three seconds,the yellow lightflash for couple times,then the co-pilot"s seat start to heat andit will find a proper temperature.nomatter whether there is some atthe co-pilot"s seat just press the button for three seconds theseat will start to work.

(5)there are two way to turn it off.first,just stopthe car.if only the driver"s seat is working put the level at whenthe green light is flashing then press one more time it will stopheating.second press the button for three seconds.

4 his product is easy to install,easy to use,couldcontroll two seats by one controller and have five levels.