品牌光洋歐克型號31930種類其他材料金屬制作工藝集成輸出信號脈沖

●特征properties:

◇探頭安裝時沒有刻線標志及方向性要求。
◇用在齒輪、齒條或凹凸不平的導磁金屬上，作計數、定位、檢測。被測齒輪的齒間距可以小到1.5-2mm。
◇輸出接線為npn型、pnp型通用。
◇耐惡劣環境，如油、水、粉塵等。
◇具的分辨率和極高的重復性。
◇寬頻響，可在80hz~33khz中使用。
◇抗電磁干擾大。
◇適用于村田33h加彈機、no741、777、778……卷繞頭摩擦輥、錠子、橫動軸測速探頭，（pg1、pg2、pg3。型號pa1015a）；帝人卷繞頭錠子、橫動軸測速探頭（pu2、pu3、pu4。型號em-014）；中麗bkv系列高速卷繞頭等。

◇the probe installation has no line mark anduest.
◇applied to count, orient or test for gear, rack or uneven magneticmetal, the teeth interval of the gear wheel can be less than1.5-2mm.
◇the output terminal is npn type, pnp is common.
◇endure bad environment, such as oil, water or dust etc….
◇excellent distinguishing rate and high repetition.
◇wide band, can be used within 80hz~33khz.
◇high anti- electromagnetic interference
◇applied to murata 33h feeder, no741, 777, 778….. winding frictionstick, spindle, transverse axle velometer probe, (pg1, pg2, pg3,type: pa1015a), teijin winding spindle, transverse axle velometerprobe, (pu2, pu3, pu4, type: em-014), high speed drawing….

本產品推薦檢測間隙（探頭表面與齒頂之間）為1mm±20%，建議安裝傳感器時，用塞尺準確調整該間隙。為了使輸出達到效果，當齒輪信號頻率大于15khz，齒輪安裝的徑向跳動應小于0.03mm，當齒輪信號頻率小于15khz時，齒輪安裝的徑向跳動應小于0.1mm。
因傳感器內部有永磁體，安裝時應注意避免齒輪與傳感器頭之間因吸引而產生撞擊，而使傳感器損壞。
傳感器測量時無方向性。
注意：若周圍電磁干擾大，建議將屏蔽線妥善接地，接地位置在接收裝置輸入端的地線點上。
the recommend testing clearance (between surface of probe and toothtop) is 1mm ±20%, suggest to adjust the clearance with proof stickwhile install the sensor. in order to make output to be besteffect, if the gear signal frequency is larger than 15 khz, makesure the radial beats of gear to be less than 0.1mm, while the gearsignal frequency is smaller than 15 khz, the radial beats could beless than 0.3mm.
for there are permanent magnet inside the sensor, please avoidimpact on the sensor, and result in sensors" damage.
the sensor has no direction re when do measurement.
note: if the electromagnetic disturbance around is strong, suggestmake proper ground to screened cable, the ground position should beplaced at the gnd point of input terminal of receivinge